Wattyl has a wide range of Protective and Industrial Coating products that may be used in combination to make hundreds of different coating systems. This guide is designed to assist in the selection of the correct coating system for your application by providing Wattyl’s most common coating systems for typical substrates and exposure environments.
System selection is a function of: exposure environment, expected life, substrate material, substrate condition, previous coating (if present), surface preparation method, application method, application conditions and requirements, structure design.
Correct surface preparation is critical to the longevity of any coating system. For details of surface preparation methods refer to the surface preparation sections (I-10 to I-14) of the Wattyl Protective and Marine Coatings Manual along with the appropriate Australasian Standards. For further assistance with system selection for a specific project please contact your local Protective and Industrial Coatings Sales Representative or contact Wattyl on 0800 735 551
PROTECTIVE SYSTEMS - ATMOSPHERIC
MILD STEEL - MILD ATMOSPHERIC ENVIRONMENT (VERY LOW CORROSIVITY)
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Power tool clean Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Power tool clean to AS1627.2 Class 2 (min.) |
NZ8050 | 1 | P33.03 | Epinamel DTM985 | 150 | Single coat, surface tolerant, epoxy mastic. Excellent corrosion resistance. Full AS2700 colour range available. |
NZ7002 | 1 2 3 | WM304 WM321 WM321 | Rapid Primer Longlife Enamel Longlife Enamel | 50 35 35 | Economical alkyd system with a full gloss finish. Wide colour offer available. |
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
NZ7003 | 1 | P42.02 | Galvit ES600 | 75 | Single coat, zinc rich ethyl silicate primer/finish for excellent protection of steel. Approved to APAS2908, APAS2973, A3750.15 Type 4. |
NZ7004 | 1 | P42.01 | Galvit ES510 | 75 | Single coat, zinc rich ethyl silicate primer/finish for excellent protection of steel. More economical than Galvit ES600 system, due to lower zinc content. Approved to APAS2908. |
NZ7005 | 1 2 | P30.01 P50.01 | Epinamel PR250 Poly U400 | 75 50 | Highly durable epoxy/polyurethane system with a hard wearing, high gloss finish. Full AS2700 colour range available. |
NZ7006 | 1 2 | P30.01 P51.02 | Epinamel PR250 Poly U750 | 75 100 | High build, highly durable epoxy/polyurethane system with a hard wearing, gloss finish. Full AS2700 colour range available.
|
MILD STEEL - MODERATE ATMOSPHERIC ENVIRONMENT (LOW CORROSIVITY)
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Power tool clean Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Power tool clean to AS1627.2 Class 2 (min.) |
NZ7007 | 1 2 3 | WM304 WM321
WM321 | Rapid Primer Longlife Enamel Longlife Enamel | 75 35 35 | Medium build, gloss alkyd system with a high film build primer for extra protection. Brush and roll system. Wide colour offer available. |
NZ7008 | 1 2 | P30.01 P50.01 | Epinamel PR250 Poly U400 | 100 50 | Highly durable epoxy/polyurethane system with a hard wearing, high gloss finish. Full AS2700 colour range available. |
NZ7009 | 1 2 | P30.01 P51.02 | Epinamel PR250 Poly U750 | 100 100 | High build, highly durable epoxy/polyurethane system with a hard wearing, gloss finish. Full AS2700 colour range available. |
NZ7010 | 1 | P33.03 | Epinamel DTM985 | 200 | Single coat, surface tolerant, epoxy mastic. Excellent corrosion resistance. Full AS2700 colour range available. |
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
NZ7011 | 1 2 | P30.01 P50.01 | Epinamel PR250 Poly U400 | 100 50 | Highly durable epoxy/polyurethane system with a hard wearing, high gloss finish. Full AS2700 colour range available. |
NZ7012 | 1 2 | P30.01 P51.02 | Epinamel PR250 Poly U750 | 100 100 | High build, highly durable epoxy/polyurethane system with a hard wearing, gloss finish. Full AS2700 colour range available. |
NZ7013 | 1 | P33.01 | Epinamel DTM800 | 200 | Single coat, surface tolerant, epoxy mastic. Excellent corrosion resistance. Full AS2700 colour range available. |
NZ7015 | 1 2 | P41.02 P31.01 | Galvit EP102 Epinamel EB600 | 50 150 | A high build, full epoxy system with a zinc rich primer for long lasting protection. |
MILD STEEL - TROPICAL ATMOSPHERIC ENVIRONMENT (MEDIUM CORROSIVITY)
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Power tool clean Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Power tool clean to AS1627.2 Class 2 (min.) |
NZ7016 | 1 2 3 | P30.01 P31.01 P50.01 | Epinamel PR250 Epinamel EB600 Poly U400 | 75 100 50 | High gloss epoxy/polyurethane system with very good durability. Full AS2700 colour range available. |
NZ7017 | 1 2 3 | P30.01 P31.01 P51.02 | Epinamel PR250 Epinamel EB600 Poly U750 | 75 100 100 | Gloss, high build, epoxy/polyurethane system with very good durability. Full AS2700 colour range available. |
NZ7018 | 1 2 | P30.01 P31.01 | Epinamel PR250 Epinamel EB600 | 75 150 | High build, epoxy system with long-term recoatability and curing at low temperatures. Full AS2700 colour range available. |
NZ7019 | 1 2 | P33.03 P33.03 | Epinamel DTM985 Epinamel DTM985 | 150 150 | High build, high solids, epoxy mastic system, excellent anticorrosive performance. Full AS2700 colour range available. |
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
NZ7020 | 1 2 | P30.01 P50.01 | Epinamel PR250 Poly U400 | 200 50 | Highly durable system with a hard wearing, high gloss finish. Full AS2700 colour range available. |
NZ7021 | 1 2 3 | P42.01 P31.01 P50.01 | Galvit ES 510 Epinamel EB600 Poly U400 | 75 100 50 | A high gloss finish, zinc rich ethyl silicate/epoxy/polyurethane system for best anticorrosive protection. Full AS2700 colour range available. |
NZ7022 | 1 2 | P33.03 P33.03 | Epinamel DTM985 Epinamel DTM985 | 150 150 | High build, high solids, epoxy mastic system, excellent anticorrosive performance. Full AS2700 colour range available. |
NZ7023 | 1 2 | P30.01 P31.01 | Epinamel PR250 Epinamel EB600 | 75 150 | High build, epoxy system with long-term recoatability and curing at low temperatures. AS2700 colour range available. |
NZ7024 | 1 2 | P30.01 P51.02 | Epinamel PR250 Poly U750 | 150 100 | High build, highly durable system with a hard wearing, gloss finish. Full AS2700 colour range available. |
NZ7025 | 1 2 3 | P41.02 P31.01 P50.01 | Galvit EP102 Epinamel EB600 Poly U400 | 50 125 50 | An epoxy zinc/epoxy/polyurethane system for excellent durability and protection. Full AS2700 colour range available. |
MILD STEEL - MARINE ATMOSPHERIC ENVIRONMENT (HIGH CORROSIVITY)
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
|
Power tool clean Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Power tool clean to AS1627.2 Class 2 (min.) |
NZ7026 | 1 2 | P33.03 P50.01 | Epinamel DTM985 Poly U400 | 300 50 | A high build, surface tolerant epoxy mastic, high gloss polyurethane system with excellent anticorrosive performance. Full AS2700 colour range available. |
NZ7027 | 1 2 | P33.03 P51.02 | Epinamel DTM985 Poly U750 | 250 100 | A high build, surface tolerant epoxy mastic, high build gloss polyurethane system with excellent anticorrosive performance. Full AS2700 colour range available. |
NZ7028 | 1 2 | P30.01 P33.03 | Epinamel PR250 Epinamel DTM985MIO | 75 325 | A high build, high solids, epoxy system with micaceous iron oxide finish coat for excellent corrosion protection. |
|
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
NZ7029 | 1 2 | P33.03 P50.01 | Epinamel DTM985 Poly U400 | 300 50 | A high build, surface tolerant epoxy mastic, high gloss polyurethane system with excellent anticorrosive performance. Full AS2700 colour range available. |
NZ7030 | 1 2 | P33.03 P51.02 | Epinamel DTM985 Poly U750 | 250 100 | A high build, surface tolerant epoxy mastic, high build gloss polyurethane system with excellent anticorrosive performance. Full AS2700 colour range available. |
NZ7031 | 1 2 3 | P41.02 P33.03 P50.01 | Galvit EP 102 Epinamel DTM985MIO Poly U400 | 50 200 50 | A high build, high gloss, high solids epoxy micaceous iron oxide system with a zinc rich primer for excellent corrosion protection. Full AS2700 colour range available. |
NZ7032 | 1 2 3 | P41.02 P33.03 P51.02 | Galvit EP102 Epinamel DTM985MIO Poly U750 | 50 150 100 | A high build, gloss, high solids epoxy micaceous iron oxide system with a zinc rich primer for excellent corrosion protection. Full AS2700 colour range available. |
NZ7033 | 1 2 | P41.02 P33.03 | Galvit EP102 Epinamel DTM985MIO | 50 200 | A high build, high solids epoxy micaceous iron oxide system with a zinc rich primer for excellent corrosion protection. |
NZ7034 | 1 2 3 | P42.01 P33.03 P50.01 | Galvit ES510 Epinamel DTM985 Poly U400 | 75 200 50 | A highly durable, high gloss polyurethane finish with zinc rich primer and high solids epoxy build coat. Excellent long term performance. Full AS2700 colour range available. |
NZ7035 | 1 2 3 | P42.01 P33.03 P51.02 | Galvit ES510 Epinamel DTM985 Poly U750 | 75 150 100 | A highly durable gloss polyurethane finish with zinc rich primer applied over a high solids epoxy build coat. Excellent long term performance. Full AS2700 colour range available. |
NZ7036 | 1 2 | P42.01 P33.03 | Galvit ES510 Epinamel DTM985 | 75 200 | A high build, high solids epoxy with a zinc rich ethyl silicate primer. Full AS2700 colour range available.
|
MILD STEEL - SEVERE MARINE ATMOSPHERIC ENVIRONMENT (VERY HIGH CORROSIVITY)
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Power tool clean Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Power tool clean to AS1627.2 Class 2 (min.) |
NZ7037 | 1 2 | P33.03 P50.01 | Epinamel DTM985 Poly U400 | 300 50 | A high build, surface tolerant epoxy mastic, high gloss polyurethane system with excellent anticorrosive performance. Full AS2700 colour range available. |
NZ7038 | 1 2 | P33.03 P51.02 | Epinamel DTM985 Poly U750 | 250 100 | A high build, surface tolerant epoxy mastic, high build gloss polyurethane system with excellent anticorrosive performance. Full AS2700 colour range available. |
NZ7039 | 1 2 | P30.01 P33.03 | Epinamel PR250 Epinamel DTM985MIO | 75 325 | A high build, high solids, micaceous iron oxide epoxy system for excellent corrosion protection. |
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
NZ7040 | 1 2 3 | P30.01 P33.03 P50.01 | Epinamel PR250 Epinamel DTM985 Poly U400 | 75 250 50 | A high build, high solids epoxy/high gloss polyurethane system for excellent corrosion protection. Full AS2700 colour range available. |
NZ7041 | 1 2 3 | P30.01 P33.03 P51.02 | Epinamel PR250 Epinamel DTM985 Poly U750 | 75 200 100 | A high build, high solids epoxy/gloss polyurethane system for excellent corrosion protection. Full AS2700 colour range available. |
NZ7042 | 1 2 | P33.03 P33.03 | Epinamel DTM985 Epinamel DTM985 | 200 200 | A high build, high solids, surface tolerant, epoxy mastic system. Excellent corrosion resistance. Full AS2700 colour range available. |
NZ7081 | 1 2 3 | P41.02 P33.03 P51.02 | Galvit EP102 Epinamel DTM985MIO Poly U750 | 50 200 100 | A high build, high solids epoxy micaceous iron oxide, gloss polyurethane system with a zinc rich primer for excellent corrosion protection. Full AS2700 colour range available. |
MILD STEEL - WET ABRASIVE BLAST OR HYDROJET SURFACE PREPARATION
- FOR MILD, MODERATE, TROPICAL, INDUSTRIAL AND MARINE ATMOSPHERIC ENVIRONMENTS
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Pretreatment Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Followed by either: Wet abrasive blast Wet abrasive blast clean the surface to remove all millscale, rust, old paint and achieve a surface similar to AS1627.4 Class 2½. Flash rusting will occur almost immediately. High pressure water wash using clean and fresh water to remove all blasting residue. Allow all surfaces to dry before painting. or Ultra high pressure water jet Ultra high pressure water jet (UHPWJ) >170 MPa (>25,000 psi) the surface using fresh and clean water to remove all millscale, rust, old paint and achieve a surface similar to AS1627.4 Class 2½. Flash rusting will occur almost immediately. Allow all surfaces to dry before painting. |
NZ7043 | 1 2 3 | P30.01 P33.03 P50.01 | Epinamel PR250 Epinamel DTM985 Poly U400 | 75 250 50 | A high build, high gloss polyurethane system with very good durability. Full AS2700 colour range available. |
NZ7044 | 1 2 3 | P30.01 P33.03 P51.02 | Epinamel PR250 Epinamel DTM985 Poly U750 | 75 200 100 | A high build, gloss polyurethane system with very good durability. Full AS2700 colour range available. |
NZ7045 | 1 2 | P30.01 P33.03 | Epinamel PR250 Epinamel DTM985 | 75 300 | A high build, high solids epoxy system with excellent corrosion protection. |
GALVANISED STEEL, ALUMINIUM OR FIBRE GLASS
- MILD, MODERATE, TROPICAL, INDUSTRIAL AND MARINE ATMOSPHERIC ENVIRONMENTS
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Pretreatment Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth (where applicable). Follow by the surface preparation for the appropriate substrate, refer below: GALVANISED STEEL - Lightly abrasive blast using an inert grit to achieve a roughened, uniform flat appearance over the entire surface. Do not disturb zinc layer during blasting. ALUMINIUM - Either lightly abrasive blast clean using an inert grit to achieve a uniform, flat appearance over the entire surface; or mechanically abrade the entire surface using 80 grit paper/disc. FIBRE GLASS - Mechanically abrade the entire surface using 80 grit paper/disc. |
NZ7046 | 1 2 3 | WA106
WM321
WM321 | Killrust Super Etch Longlife Enamel Longlife Enamel | 10 35 35 | A medium build, single pack etch primer with a gloss alkyd finish. Wide colour offer available. Suitable for mild exposure environments only. |
NZ7047 | 1 2 3 | P30.01 P33.03 P50.01 | Epinamel PR250 Epinamel DTM985 Poly U400 | 75 250 50 | High build, gloss polyurethane system with excellent durability. Full AS2700 colour range available. Suitable for all exposure environments. |
NZ7048 | 1 2 3 | P30.01 P33.03 P51.02 | Epinamel PR250 Epinamel DTM985 Poly U750 | 75 200 100 | High build, gloss polyurethane system with excellent durability. Full AS2700 colour range available. Suitable for all exposure environments. |
NZ7049 | 1 2 | P30.01 P50.01 | Epinamel PR250 Poly U400 | 75 50 | Highly durable system with a hard wearing, high gloss finish. Full AS2700 colour range available. Suitable for mild and moderate exposure environments. |
NZ7050 | 1 2 | P30.01 P51.02 | Epinamel PR250 Poly U750 | 75 100 | High build, highly durable system with a hard wearing, gloss finish. Full AS2700 colour range available. (Suitable for mild and moderate exposure environments.) |
CONCRETE - DECORATIVE SYSTEMS (excluding floors)
- FOR MILD, MODERATE, TROPICAL, INDUSTRIAL AND MARINE ATMOSPHERIC ENVIRONMENTS
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Pretreatment New concrete shall be at least 28 days old prior to application of coating system. Remove all surface contaminants (including bondbreakers and curing agents) followed by either: Abrasive blast Abrasive blast to remove all laitance and other surface contaminants. Ensure the concrete moisture content is less than 4%; or Acid etch Acid etch the surface using a solution of hydrochloric acid. Rinse the surface with copious quantities of clean, fresh water to remove all of the acid residue. Allow the concrete to dry. Ensure the concrete moisture content is less than 4%. |
NZ7051 | 1
2
3
| TA062
TA062
TA062
| Aquafloor Waterbased Epoxy Aquafloor Waterbased Epoxy Aquafloor Waterbased Epoxy | 35
35
35 | Epoxy gloss system for simplified on-site application. Full AS2700 colour range available. |
NZ7052 | 1 2 | WM305 P31.01 | Estathane Epoxy Primer Epinamel EB600 | 35 100 | A highly durable medium solids epoxy satin system. Full AS2700 colour range available. |
NZ7053 | 1 2 | WM305 P51.02 | Estathane Epoxy Primer Poly U750 | 35 100 | High build, highly durable system with a hard wearing, gloss polyurethane finish. Full AS2700 colour range available. |
PROTECTIVE SYSTEMS - IMMERSION
MILD STEEL - FRESH/SEA WATER IMMERSION
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
| | | | | | |
NZ7054 | 1 2 | P33.02 P33.02 | Epinamel DTM900 Epinamel DTM900 | 150 150 | Economical, high solids, high build, epoxy system. |
NZ7055 | 1 2 | P36.01 P36.01 | Epinamel MF920 Epinamel MF920 | 250 250 | High performance, high build, high solids, highly abrasion resistant epoxy system. |
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
NZ7056 | 1 2 3 | P30.01 P33.02 P33.02 | Epinamel PR250 Epinamel DTM900 Epinamel DTM900 | 75 150 150 | A high build, high solids epoxy system for protection against most wastewaters. |
NZ7057 | 1 2 | P36.01 P36.01 | Epinamel MF920 Epinamel MF920 | 250 250 | High performance, high build, high solids, highly abrasion resistant epoxy system. |
PROTECTIVE SYSTEMS - HEAT AND CHEMICAL RESISTANT
MILD STEEL - HEAT RESISTANT SYSTEMS
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
Interior - up to 200°C |
NZ7058 | 1 2 | P31.01 P31.01 | Epinamel EB600MIO Epinamel EB600MIO | 60 60 | Low temperature curing, recoatable epoxy micaceous iron oxide system for long term flexibility. |
NZ7059 | 1 2 | P71.03 P71.03 | Heatkote Aluminium Heatkote Aluminium | 20 20 | Aluminium pigmented, acrylic silicone system with no heat curing required. |
NZ7060 | 1 2 | WM321 WM321 | Longlife Enamel Aluminium Longlife Enamel Aluminium | 35 35 | Single product, single pack aluminium for economical protection. |
Interior - up to 400°C |
NZ7061 | 1 | P42.01 | Galvit ES510 | 75 | Single coat, zinc rich ethyl silicate system for very good heat resistance and corrosion protection. |
Exterior - up to 200°C |
NZ7062 | 1 2 3 | P31.01 P31.01 P31.01 | Epinamel EB600MIO Epinamel EB600MIO Epinamel EB600MIO | 60 60 60 | Low temperature curing, single product, recoatable epoxy micaceous iron oxide system for long term flexibility. |
NZ7063 | 1 2 3 | P42.01 P71.03 P71.03 | Galvit ES510 Heatkote Aluminium Heatkote Aluminium | 75 20 20 | Acrylic silicone finish over zinc rich ethyl silicate primer. No heat curing required. |
Exterior - up to 400°C |
NZ7064 | 1 | P42.01 | Galvit ES510 | 75 | Single coat, zinc rich ethyl silicate system for excellent heat resistance and corrosion protection. |
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
Acidic |
NZ7065 | 1 2 3 | P20.01 P21.02 P21.01 | PermaChlor PR30 PermaChlor CR60 PermaChlor CR50 | 75 100 35 | Chlorinated rubber system with very good resistance to acidic splash conditions. |
NZ7066 | 1 2 | P33.03 P51.02 | Epinamel DTM985 Poly U750 | 150 100 | High build, epoxy/gloss polyurethane system with good resistance to a range of acidic splash conditions. |
Alkali |
NZ7067 | 1 2 | P33.03 P32.02 | Epinamel DTM985 Epinamel CF602 | 150 35 | High solids, epoxy gloss finish with good resistance to a range of alkali splash conditions. |
PROTECTIVE SYSTEMS - FLOORING
FLOORING SYSTEMS - MILD STEEL
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Abrasive Blast Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth. Abrasive blast in accordance with AS1627.4 to a minimum Sa 2½ (AS1627.9) |
Semi-gloss |
NZ7068 | 1 2 | P30.01 P31.01 | Epinamel PR250 Epinamel EB600 | 150 150 | Low temperature curing, recoatable epoxy system with long term flexibility. |
NZ7069 | 1 2 | P33.03 P33.03 | Epinamel DTM985 Epinamel DTM985 | 200 200 | High build, surface tolerant, epoxy mastic system. Excellent corrosion resistance. Suitable for high traffic areas. |
NZ7082 | 1 2 | P30.01 P36.01 | Epinamel PR250 Epinamel MF920 | 75 150 | A high build, highly abrasion resistant system, suitable for high traffic areas. |
Gloss |
NZ7070 | 1 2 | P30.01 P51.02 | Epinamel PR250 Poly U750 | 75 75 | Full gloss polyurethane finish system for moderate traffic areas. |
Non-Skid |
NZ7071 | 1 2 3 | P30.01 P34.01 P51.02 | Epinamel PR250 Epinamel NS808 Poly U750 | 75 400 75 | Epoxy non-skid system with a gloss polyurethane finish, suitable for high traffic areas. |
FLOORING SYSTEMS - GALVANISED STEEL
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Abrasive Blast (whip blast) Degrease all surfaces in accordance with AS1627.1. Remove slag and splatter, grind all welds and high points smooth (where applicable). Lightly abrasive blast using an inert grit to achieve a roughened, uniform flat appearance over the entire surface. Do not disturb zinc layer during blasting. |
Semi-gloss |
NZ7072 | 1 2 | P30.01 P31.01 | Epinamel PR250 Epinamel EB600 | 75 150 | Low temperature curing, recoatable epoxy finish for long term flexibility. Suitable for moderate traffic areas. |
NZ7073 | 1 2 | P30.01 P36.01 | Epinamel PR250 Epinamel MF920 | 75 150 | A high build, highly abrasion resistant system suitable for high traffic areas. |
Gloss |
NZ7074 | 1 2 | P30.01 P51.02 | Epinamel PR250 Poly U750 | 75 100 | High build, highly durable system with a hard wearing, gloss finish. Full AS2700 colour range available. Suitable for moderate traffic areas. |
Non-Skid |
NZ7075 | 1 2 3 | P30.01 P34.01 P51.02 | Epinamel PR250 Epinamel NS808 Poly U750 | 75 400 100 | Epoxy non-skid system for high traffic areas. |
FLOORING SYSTEMS - CONCRETE
SYSTEM NO. | COAT | DATA SHEET | PRODUCT | DFT (µm) | SYSTEM BENEFITS |
|---|
Pretreatment New concrete shall be at least 28 days old prior to application of coating system. Remove all surface contaminants (including bondbreakers and curing agents) followed by either: Abrasive blast Abrasive blast to remove all laitance, unsound paint and other surface contaminants. Completely remove all dust and grit. Ensure the concrete moisture content is less than 4% or Acid etch Acid etch the surface using a solution of hydrochloric acid. Rinse the surface with copious quantities of clean, fresh water to remove all of the acid residue. Allow the concrete to dry. Ensure the concrete moisture content is less than 4%. |
|
Semi-gloss |
NZ7076 | 1 2 3 | WM305 P31.01 P31.01 | Estathane Epoxy Primer Epinamel EB600 Epinamel EB600 | 35 100 100 | Low temperature curing, Recoatable epoxy system suitable for moderate traffic areas. |
Gloss |
NZ7077 | 1 2 | WM305 P51.02 | Estathane Epoxy Primer Poly U750 | 35 100 | An epoxy, high build gloss polyurethane system suitable for moderate traffic areas. |
|
NZ078 | 1 2 3 | TA062 TA062 TA062 | Aquafloor Waterbased Epoxy Aquafloor Waterbased Epoxy Aquafloor Waterbased Epoxy | 35 35 35 | Gloss epoxy system suitable for moderate traffic areas. |
|
Non-Skid |
NZ7079 | 1 2 3 | WM305 P34.01 P51.02 | Estathane Epoxy Primer Epinamel NS808 Poly U750 | 35 400 100 | Epoxy/gloss polyurethane non-skid system suitable for high traffic areas. |
NZ7080 | 1 2 3 | WM305 P34.01 P32.02 | Estathane Epoxy Primer Epinamel NS808 Epinamel CF602 | 35 400 35 | Gloss epoxy non-skid system suitable for high traffic areas. |